NOTE: Note: Homelite used 2 different ignition manufacturers, you have to look on the flywheel to determine the manufacture of the ignition coil.This Coil Was Tested In 200 Degree Test Cell For Days With No Failures. The Company Is A OEM Supplier And Fixed The Problems With The Prestolite-Wico Blue Coils That Would Always Fail. I Went To Several Ignition Coil Companies To Find A Reliable Supplier Who Could Provide A High Quality Ignition Coil That Was Better Then The OEM. This Coil Is Made Exclusive For Performance Saw Supply In South America, The Reason We Had These Coils Made Was That The Homelite Super Xl, Xl12, Was A Fantastic Saw And When The Manufacture Decided To Quit Making These Coils And Lot Of People Were Not Happy. Note: On some saws, the ignition coil bolts onto a plastic housing with a ground wire running to the cylinder or crankcase for a ground.Homelite Super Xl, Xl12, Sxl Old Blue, Big Red Ignition Coil Replaces 94605, A94605s Wico, Prestolite. Also sand the mounting surface where the coils are attached to ensure a good and proper grounding of the ignition coil. Part: Wico Prestolite ignition coil A94325 A-94325 with points, condenser and mounting plate Condition: good used/working shape. If no spark is visible, remove the Homelite Super XL 925 Chain Saw UT-10415 ignition coil and sand the bottom of the coil. Sold Out homelite super xl, xl-12 chainsaw Wico points ignition coil kit. Removing the spark plug makes this process easier since it reduces the resistance when pulling the starter rope. Using a good quality spark tester, pull the starter rope with a good fast pull and check for spark. To test the Homelite Super XL 925 Chain Saw UT-10415 ignition coil, disconnect the ignition switch wire at the ignition coil. I wrapped the coil in aluminum foil, to keep the fumes down, set the oven at 300 degrees, and put the coil in the oven. Note: On Stihl models 031, 032 and 041 these coils have a spark advance built into them and the ignition chip will cause misfiring. I have a Super XL Automatic that I bought for twenty bucks because it had no spark. If a flywheel has more than two magnets, then the ignition chip trigger will not work. The ignition trigger replaces points and the condenser on most chain saws having just two magnets. This transfer steps up the voltage to fire the spark plug. It works by breaking the current from the primary side and sending it to the secondary side of the coil. The Homelite Super XL 925 Chain Saw UT-10415 ignition chip is a trigger device that determines when the coil needs to fire the spark plug. Then, the electronic control module trigger breaks the current and sends it to the secondary side of the coil building voltage up to 20,000 volts used to fire the spark plug. When the magnets pass the U-shaped iron cores on the ignition coil, the primary winding builds voltage up to approximately 200 volts. The flywheel has two imbedded magnets, a north and a south pole. The secondary side has very thin wire wrapped around the primary windings approximately 20,000 times. The primary side has thick wire wrapped around one leg approximately 150-200 times. The Homelite Super XL 925 Chain Saw UT-10415 ignition coil has an armature and is U-shaped with two ends facing the flywheel. Magneto ignition system which requires no battery voltage to generate Suitable Replacement Homelite Super XL 925 Chain Saw UT-10415 Ignition Coil & Chip
#Homelite super xl automatic ignition coil free
One year warranty to be free from defects and work properly. NOS Homelite 410, Super 1050, Super 1130G, Super EZ, Super XL, Super XL-925, XL-12 Chainsaw Automatic Oil Pump Plunger Cover Screw 80919 0. Ignition coils and ignition chips are very high quality and have a Replaced with our suitable replacement Homelite Super XL 925 Chain Saw UT-10415 chainsaw Ignition Coil and Chip parts below. Performance Saw Supply replacement If your chainsaw seems to not be getting a spark, then you should check the Homelite Super XL 925 Chain Saw UT-10415 Ignition Coil & Ignition Chip to see if it needs to be
0 kommentar(er)
